XTREME Original Klearkote 4.4 VOC

5 STAR XTREME AUTOBODY PRODUCTS
TECHNICAL DATA INFORMATION
DATED: JUNE 2013
PRODUCT NUMBER DESCRIPTION
#5185 – ORIGINAL KLEARKOTE 4.4 VOC
PRODUCT DESCRIPTION
5185 is a medium solids two component polyurethane clearcoat with a sprayable VOC of 4.4
lbs/gal. Formulated to offer Refinishers ease of application, great flow and leveling, superior
gloss and excellent distinctness of image in a productive 2K polyurethane clearcoat.
PRODUCTS
#5185-1 Original Klearkote, Gallon
#5185-4 Original Klearkote, Quart
*#5186 Original Hardener, Fast 4.4 VOC Quart
*#5187 Original Hardener, Medium 4.4 VOC Quart
*#5188 Original Hardener, Slow 4.4 VOC Quart
* Also available in half pints
CAUTION ACCELERATOR NOT RECOMMENDED
SURFACE PREPARATION
Apply Undercoats and Basecoat per manufacturer’s instruction. Over OEM or completely
cured previously painted substrates scuff with a grey scuff pad or 600 grit then wipe
clean with #5902 Final Wipe Surface Cleaner. Allow basecoat adequate flash time
(follow manufacturer’s recommendation) Follow basecoat manufacturer’s
recommendation for recoat intervals.
MIXING DIRECTIONS
Mix 4 parts 5185 base with 1 part 5186, 5187, or 5188 by volume. Activator selection
should be based on the size of the part to be painted and the temperature of both the air
and part at time of painting.
APPLICATION
Number of Coats: 2-3 Application Density: full wet coats
Overlap: 50% Flash: Follow recommendations in “Dry Time” section
Film Thickness Range: Dry 1 mil – 6 mils
Wet 3 mils – 6 mils
Application Conditions: Minimum Temp 50°F (Substrate Temp.)
Max Temp 100°F (Substrate Temp.)
Ambient Humidity Less than 80% preferred
POT LIFE
When properly covered at 77°F, 5185 will maintain a sprayable viscosity for at least from
3-5 hours depending on activator selection.
ADDITIVES
ACCELERATOR: N/A
FISHEYE: N/A
FLEX ADDITIVE: Not required
Note: Do not spray when surface temperature is below 50°F.
SUBSTRATES
Commercially available basecoats with a VOC of less than 6.6 lbs/gal.
Properly prepared previously painted surfaces.
CLEAN-UP & STORAGE
Clean spray equipment immediately after use with gun wash solvent.
GUN SETUPS:
CONVENTIONAL
Gravity Feed 1.3 – 1.5 mm tip
Siphon Feed 1.6 – 1.8 mm tip
HVLP 1.3 mm – 1.5 mm
AIR PRESSURES
Conventional @ Gun PANEL OVERALL
Gravity Feed 35-40 psi 45 psi
Siphon Feed 35-45 psi 45-50 psi
HVLP @ Cap 6-8 psi 9-10 psi
FLASH/DRY TIMES
5186 @ or 5187 @ or 5188 @ or
above 77ºF above 85ºF above 95ºF
Flash Between Coats 5-10 min 5-10 min 10-15 min
Dust Free 10-15 min 15 min 15-20 min
Sand/Polish 8-10 hours 10-12 hours 12-14 hours
Force Dry (Convection Heat) 5186 5187 5188
Purge time before applying heat 20 min 20 min 20 min
Force Dry Time 20 min@ 165ºF 20 min@ 165ºF 20 min@ 165ºF
Sand and Buff After Cool Down
TECHNICAL DATA
Density: 7.64 lbs/gal (unactivated)
Solids
By Weight: 36.2%
By Volume: 29.0%
VOC (Volatile Organic Content): 4.56 lbs/gal
Viscosity: 17-19 seconds Zahn #2
Flash Point: -4°F
Theoretical Coverage: 465 sq ft per gal @ 1 mil thickness
FIRST AID:
In case of eye contact, immediately flush eyes with plenty of water for at least 15
minutes and get medical attention. For skin: Wash thoroughly with water. If difficulty in
breathing is experienced, get medical attention immediately. If swallowed, do not induce
vomiting, get medical attention immediately. See Material Safety Data Sheet.
SAFETY INFORMATION – FOR INDUSTRY USE ONLY
Danger: Vapor and spray mist harmful. Overspray may cause lung damage. May cause
allergic skin and respiratory reaction, effects may be permanent. Flammable liquid and
vapor. Harmful if inhaled.May affect the brain or nervous system causing dizziness,
headache, or nausea. May cause eye, skin, nose, and throat irritation. Contents: See
product label for contents and CAS #’s.The contents of this package must be blended
with other components before the product can be used. Any mixture of components will
have hazards of all components. Before opening the packages, read all warning labels.
Follow all precautions. The material is designed for application only by professional
trained personnel using proper equipment under controlled conditions, and is not
intended for sale to the general public.
KEEP OUT OF REACH OF CHILDREN.